Tool Belt With 6 Bags To Load 24 Spool of Wires and Hold 2 pcs of Rebar Tying Machines

Tool Bag (bag) could load max 24 spools of wire and hold 2 pcs of rebar tying machines at the same time

Rebar Tying Machine, Rebar Tying Tool, Rebar Tier, Rebar, Hand tool, Hand-hold tool, tying tool, knoting tool, tier, hardware tool, tool belt, tool bag,spool wire, wire spool,tying wire,tying spool

Product Name: Tool Belt With 6 Bags To Load 24 Spool of Wires and Hold 2 pcs of Rebar Tying Machines

Model No.: TB-0624

Product Descriptions:- Bag Qty: 6 pcs.- Spool Qty Per Bag: 4 pcs.- Max Loading Qty: 24 Spools- Unit Holding Qty: 2 pcs Rebar Tying Machines- Adjustable Waistline: 86-120 cm - Dimensin: 130 (L) x 7 (W) cm- Convenient and friendly for left-handed or right-handed person to hold the machine- One loop at left side for left-handed person and another one at right side for right-handed person.- Coul load max 24 spools of wires at the same time- Good quality of canvas material

Rebar Tying Machine, Rebar Tying Tool, Rebar Tier, Rebar, Hand tool, Hand-hold tool, tying tool, knoting tool,tier, hardware tool, wire, rebar tier wire, rebar tool wire, plastic cover wire for rebar tier, spool wire, plastic coated wire for rebar tier,construction tool, banding tool, binding tool,banding tier, banding tier,banding wire,binding wire,aumatical tying tool,automatic tier,automatic tying machine.

Rebar Tying, Rebar Tier. Hand-held Automatic Rebar Tying machine can tie the rebar automatically and quickly by itself.

Hand-held Automatic Rebar Tying Machine, a hand-held portable electrical tool, can knot the rebar automatically and quickly by itself. It is 5-6 times of higher efficiency than a professional worker. It is powered by a rechargeable battery which can be used alternatively and continuously during the tying working. The tying process can be completed by putting the machine jaw on the crossed rebars and then pulling the trigger only.

It greatly saves the labor cost and highly improves working efficiency, which is more helpful for you to carry out the targeted schedule as planned. It is very easy and simple to operate. Now it is more and more popular in building sites.

Before injecting the concrete during the construction of building, road, bridge, etc., ironworkers tie rebar by hand with pliers and tie wire. This work requires repeated, fast hand and arm movements while applying a lot of force. If you tie rebar at ground level, you also have to work in a stooped position with your body bent deeply forward. Tying rebar by hand greatly increases your chance of developing hand-wrist disorders due to the high hand forces used to grip pliers, the rapid hand movements used to wrap and twist wire, and the high pressure on the hand and fingers when twisting and cutting wire. If you work at ground level, you also are at risk of low back injuries from frequent and prolonged stooping and bending.

Use a Rebar Tying Machine. This lowers your risk of hand and wrist injury because it eliminates the frequent rapid hand motions required when using pliers. Some rebar tiers allow you to work standing up, so there is less stress on your low back due to stooping and bending.

Safety and health experts believe there is a risk reduction. Biomechanical research shows that high compression forces occur in the spine while stooping, and that sustained or repeated flexion of the spine may decrease the stability of the lower back and increase the risk of fatigue, leaving the back more vulnerable to injury.

While there is considerable research that shows that working in stooped, kneeling and squatting postures can cause low back disorders, the research mostly focuses on those postures in combi-nation with other risk factors such as bending or twisting or heavy loads. The literature combining stooped, squatting or kneeling postures with load handling shows rapid and severe spinal damage. There is much less in the literature regarding the health effects of these postures in an unloaded situation - that is, stooping without lifting.

However, safety and health experts believe that it is important to avoid prolonged and repeat forward bending of the back (stooping) even in the absence of the other risk factors for low back disorders. Safety and health experts believe there is an increase in productivity. Workers should experience fewer injuries. Studies conducted by NIOSH and the Construction Safety Association of Ontario (Canada) compared manual methods and one model of power tying tool, and showed that using the power tool may reduce the risk of injury to workers' hands, wrists, and low back.

Tool Belt With 6 Bags To Load 24 Spool of Wires and Hold 2 pcs of Rebar Tying Machines